![]() Line Lock-Out prevents tool from operating should voltage be restored to an interrupted line 1/2 inch capacity, 7.2 amp motor, 600 RPM All you need is a bit and you are ready to drill into any ferrous material 1/2 in. This combination unit features the 4203 adjustable position, variable speed base and the 4253-1 1/2 in. Simple two-button control panel - unobstructed by feed handleĪdjustable Position Electromagnetic Drill Press Model 4204-1.Two positions for feed handle - relocate without tools.Milwaukee Electromagnetic Drill Press 4270-20 Features The feed handle can be conveniently relocated to the opposite side without the use of tools. The simple two-button control panel is located on the back, away from feed handle obstruction. The strong two-coil magnet provides 2,300 lbs. Weldon shank cutters, or an optional 3-jaw chuck is available for use with twist drill bits. The tool is setup to accept standard 3/4 in. thick steel with annular cutters, or 1/2 in. This drill press includes a very powerful 1.1 maximum horsepower, 9.0 amp motor. However, power was not sacrificed for portability. The entire tool weighs just 26-1/2 pounds and has a comfortable carrying handle well positioned for balance, with cutter wrenches stored on-board. Push a drill button for forward or reverse.Compact Electromagnetic Drill Press - 4-20įor remote drilling in metal, the 4270-20 is a great choice. If the light is flashing, checkįor the following: Low voltage at plug Loose motor connection Mag panel buttons are jammed or stuck If flashing light still occurs, take entire unit to an authorized serviceģ. Push the magnet button to activate the magnet. On the magnet, the drill buttons will not function. If the operator attempts to start the drill before turning 6E) The drill will not operate unless the magnet button is pushed and the red The red indicatorĭrill and Magnet Interlock (Fig. To turn the magnet off, push the Magnet button. To turn the magnet on, push the Magnet button. 6D) The magnet button must be activated before the drill will run. The tool is under load, or when the tool has stopped. NOTE: To avoid damage to the gearbox, do not shift at full speed, when To change speeds, turn the drill off and rotate the lever up or down while Speed for large diameter bits and high speed for small diameter bits (see 4292-1 operate in either high or low speed. Replace the knurled collar and tighten.Ĭat. Replace the Morse Taper Socket by aligning the notches with tabsĤ. Strike the bit tang firmly with a soft metal mallet or strike the bit tangģ. Unscrew the knurled collar and remove the entire Morse Taper Socket. To remove a bit or adapter from the socket: 1. Press the taper firmly into the socket, or use the feed handle to press ![]() Slides into the slot at the top of the socket.ģ. Insert the taper into the socket and rotate the taper until the bit tang Make sure the taper is clean and lightly oiled. To insert a bit or adapter into the socket: 1. Clockwise (Tighten) - Counterclockwise (Loosen) To remove the bit, insert the chuck key into one of the three holes in Place the chuck key in each of the three holes in the chuck, turning Center the bit in theĬhuck jaws and lift it about 1/32" off of the bottom. When using drill bits, insert the bit into the chuck. Open the chuck jaws wide enough to insert the bit. Move the housing to position the drill bit over the center of the hole.ġ. Loosen the adjusting handle located at the back of the housing base. Position the magnetic base so that the drill bit is near the desired hole Remove the chain (if drilling overhead or on a vertical surface). ![]() Drill hole (see Using Twist Drills" and "Using MILWAUKEE STEELĩ. Push the forward or reverse button as required. Check the gear speed setting and change if required. Attach the safety chain if drilling overhead or on a vertical surface. Position the unit so that the tip of the drill bit is directly over theĤ. Place the magnetic drill press on a prepared surface. Taper Socket and Using Twist Drills" and "Using MILWAUKEEĢ. Insert the bit into the chuck or socket (see Keyed Chuck" or "Morse The gear shift on the drill motor is labeled:
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |